replace case this replacing case is used in a situation where compact controller e series and f series are replaced with compact controller m series. this product is convenient when wiring from the duct is dif- ficult. it results in substantial labor savings. specifications 1.types of compact controller m series models that may be built-in data sheet pdze 2. number of input/output points the specification such as the influence of the accuracy and environment corresponds to the specification for compact controller m series. 2-1 analog inputs ?points : max. 7 points ?kind of input : voltage input ?input range : 1 to 5v dc note: the opening input of an step output type controller is applicable to voltage input specification only. 2-2 analog outputs 1) control output or manipulated output ?points : 1 point ?output signal : 4 to 20ma dc note: this function is valid only with a continuous output type controller or a continuous output type manual loader. 2) auxiliary analog output ?points : 5 points ?output signal : 1 to 5v dc 2-3 digital inputs /outputs 1) auxiliary digital input signals ?points :9 points 2) control output signal (pulse width output ?o? ?points :1 set (2 points) note: this function is valid only with an step output type controller. important: externally cross-connect the control outputs to prevent the increasing pulse and the decreasing pulse from being turned on at the same time. 3) fault output signal (?lt? ?points :1 point 4) auxiliary digital output signal ?points :10 points (with a continuous output type instrument or an electronic type indicator) 8 points (with an step output type controller) 3. operation ambient specifications ?dielectric strength : 500v ac 1 minute (between power terminals vp, pc and ground terminal) 500v ac 1 minute (between signal terminals and ground terminal) ?insulation resistance : 500v dc, 50m ? or more ?grounding : d-class grounding ?insuration location : at room ?ambient temperature : 0 to 50?c (but, 40?c or less when multi- row/-tier mounting) ?temperature change ratio : 10?c/h or less ?ambient humidity : 5 to 90%rh (not condensed) ?continuous vibration : not specified. provide a support in the panel, which should be fixed to the case for vibration resistance. ?altiude : 2000m or lower above the sea level continuous output type controller, continuous output type manual loader, y d 1 2 1 2 y m y m y m y m y d y m y m step output type controller, continuous output type setter, continuous output type ratio setter, electronic indicator, model : pda211a y -b model : pdb111a2-ba a model : pdc211a2-b y y model : pdf111a2-bry ry model : pdg111a y -bry ry model : pdj111a2-byy date EDS11-139A jan. 8, 2008
pdze 2 ?transport and storege : temperature ; -20 to 70?c temperature change ratio ; 10?c/h or less humidity ; 5 to 95%rh (not con- densed) shock ; not specified 4. structure ?case : stainless steel ?finish color of case : munsell n1.5 ?protection : not protected ?external dimensions : 70.5 (w) 180max (h) 403 (d) mm depth from front panel (including termi- nal cover) ?mass : approx. 1.5kg (without cc-m main unit) ?mounting method : flash on indoor panel 68 +0.7 0 138 +1 0 250min. (72.2n-4) +1 0 138 +1 0 250min. panel 144 72 180max support panel thickness 8mm or less cc-m (excluded from scope of delivery) 67 153 replace case terminal bolt fixing metal 375 403 100min. 200min mounting one unit mounting n units n 2 n ? q'ty panel cutout outline diagram (unit : mm) ? mounting angle :a llowable within backward angle 0 to 45, not allowable down ward 5. type designation pdze1003 (continuous output type controller, continu- ous output type instrument and electronic type indica- tor) pdze2003 (step output type controller: corresponds to pdc only) 6. scope of supply replacing case fixture 1, bolt 1, mounting hardware 1 instruction manual (cc-m main unit is not included. it is to be ordered separately.) (supporting hardware is not included. kindly use existing hardware.) 45 ? 90
3 external connection diagram 11 12 int 13 smv 31 32 33 flt 11 12 int 13 smv 31 32 33 flt (unused) (di) (di) (unused) (unused) (do) note : continuous output type setter, ratio setter or electronic indicator is to be connected to this terminal. provided, however, that control output terminal cannot be used. note : continuous output type setter, ratio setter or electronic indicator is to be connected to this terminal. note : step output type controller is to be connected to this terminal 51 kpv 52 sv 53 ao1 54 ao2 55 sc 56 sc 57 mv 58 mi 59 mi 60 g 61 pc 62 grounding 24v instrament power supply- dio power supply- pcd 71 pv 72 cas 73 ai1 74 ai2 75 ai3 76 ai4 77 ai5 78 h 79 l 80 81 vp 82 vpd 13 di5 14 pv-trk 15 r-ack 16 di1 17 di2 18 di3 19 di4 20 21 do8 22 mv 1 2 3 pcd 4 ao1 5 ao2 6ai1 7ai2 8ai3 9al4 10 ai5 11 sc 12 vpd 23 h 24 l 25 26 27 28 do1 29 do2 30 do3 31 do4 32 do5 33 do6 34 do7 (do) (do) (unused) 24v instrament power supply+ dio power supply+ v v v v (continuous output type instrument) pdze1003 screw terminal area multi connector area (continuous output type controller / operator) analog output (1-5v) control output (4-20ma) v 51 kpv 52 sv 53 ao1 54 ao2 55 sc 56 sc 57 58 wo 59 w 60 g 61 pc 62 grounding 24v instrument power supply - dio power supply - pcd 71 pv 72 cas 73 74 ai2 75 ai3 76 ai4 77 ai5 78 po 79 po 80 81 vp 82 vpd 13 di5 14 pv-trk 15 r-ack 16 di1 17 di2 18 di3 19 di4 20 21 do8 22 mv 1 2 3 pcd 4 ao1 5 ao2 6 7ai2 8ai3 9al4 10 ai5 11 sc 12 vpd 23 h 24 l 25 26 27 28 29 30 do3 31 do4 32 do5 33 do6 34 do7 control output + control output - (unused) 24v instrument power supply + dio power supply + v v v v (step output type controller) analog input (1-5v) (unused) (di) (di) (unused) (unused) (do) (step output type controller ) pdze2003 screw terminal area multi connector area analog output (1-5v) analog input (1-5v) v note: open input is 1 to 5 v dc. in the case of resistance input (potentiometer input), apply voltage with potentiometer input converters placed before and after. note: externally cross-connect the control outputs. po po m l 1 l 2 +
pdze 4 isolated blocks denotes isolation power supply vp, pc ground g pv cas di do ai mi ao power supply section ground digital input digital output analog input section analog output section
5 2 pdze1003 3 cc-m (pda) t erminal no. t erminal name t erminal no. t erminal name t erminal no. t erminal name t erminal no. t erminal name t erminal no. t erminal name t erminal no. t erminal name t erminal no. t erminal name t erminal no. t erminal name t erminal name replace case terminal controller (type pmk-3/cc-f) controller (type pma-3/cc-e) controller (type pna/cc-s) manual loder (pmb) setter (pmf) ratio setter (pmg) remarks 11 i 171 pv 7 1pv71pv11i 31 pv 31 pv 31 pv analog input 14 i 272 cas 72 cas 72 cas 71 cas 33 cas 33 cas analog input 31 flt 33 flt 33 flt 33 flt 34 flt digital output 55 ao5 57, m22 mv 57, m22 mv 76 mv 54 mv 35 mv 35 so analog output 52, m6 ao2 54, m5 ao2 54, m5 ao2 analog output 53 ao3 51 kpv 51 kpv 51 kpv 51 kpv analog output 54 ao4 52 sv 52 sv 52 sv 52 sv 34 sv 34 sv analog output 51, m5 ao1 53, m4 ao1 53, m4 ao1 53 ao1 53 ao1 analog output 56, 57,m11 sc 55, 56,m11 sc 55, 56,m11 sc 54, 55 sc 55, 76 sc 32 sc 32 sc 32 sc signal common 62,m12,m34 pcd 62, m3 pcd 62, m3 pcd 62 pcd 61 pcd 16 pc note1 16 pc note1 16 pc note1 digital common 63 g 60 g 60 g 60 g 62 g g g g g g g grounding 64 n/ 61 pc 61 pc 61 pc 60 pc 16 pc note1 16 pc note1 16 pc note1 instrument power supply - 71, m7 ai1 73, m6 ai1 73, m6 ai1 73 ai1 72 ai1 33 ai1 33 ai1 33 ai1 analog input 72, m8 ai2 74, m7 ai2 74, m7 ai2 74 ai2 73 ai2 analog input 73, m9 ai3 75, m8 ai3 75, m8 ai3 75 ai3 74 ai3 analog input 74, m10 ai4 76, m9 ai4 76, m9 ai4 analog input 75 ai5 77, m10 ai5 77, m10 ai5 analog input 77 mi 158 mi 58 mi 56 mi 56 mi 36 mi control output 78 mi 159 mi 59 mi 57 mi 57 mi 37 mi control output 82, m33 vpd 82, m12 vpd 82, m12 vpd 82 vpd 82 vpd 15 vp note1 15 vp note1 15 vp note1 digital power supply + 83 l/ 81 vp 81 vp 81 vp 81 vp 15 vp note1 15 vp note1 15 vp note1 instrument power supply + m13 di1 m16 di1 m16 di1 31 pi 32 pi 12 pi 12 pi digital input m14 di2 m17 di2 m17 di2 32 pi 33 pi 13 pi 13 pi digital input m15 di3 m18 di3 m18 di3 digital input m16 di4 m19 di4 m19 di4 digital input m17 di5 m13 di5 m13 di5 80 ex-mc di2 79 ex-mc di2 digital input m19 di7 m14 pv-trk m14 pv-trk 79 pv-trk 80 pv-trk di1 digital input m20 di8 m15 r-ack m15 r-ack 78 r-ack 78 r-ack di3 digital input m21 di9 12 int digital input m22 di10 13 smv 13 smv 13 smv 15 smv 12 mc digital input m23 do1 m28 do1 m28 do1 digital output m24 do2 m29 do2 m29 do2 digital output m25 do3 m30 do3 m30 do3 digital output m26 do4 m31 do4 m31 do4 digital output m27 do5 m32 do5 m32 do5 digital output m28 do6 m33 do6 m33 do6 11 m 13 m 11 m 11 l 11 l digital output m29 do7 m34 do7 m34 do7 12 ls 14 ls do1 digital output m30 do8 m21 do8 m21 do8 77 r-req 77 r-req digital output m31 do9 m23, 78 h m23, 78 h 58 h 58 h digital output m32 do10 m24, 79 l m24, 79 l 59 l 59 l digital output note2 replaced instruments list of terminal numbers and terminal names corresponding to the replacing case and cc-m (wiring should be performed so as to coincide the terminal name of the replaced type with that of the replacing case). note: terminal numbers on left of each model note: terminal names on right of each model note1: connect pc and vp wires to pc and pcd, and vp and vpd, respectively, of the replace case. note2: in case of soft connection (wafer connection) with cc-m, confirm the replace case and cc-m terminals. common: screw terminals ?? ?i+? ?i-? ?di?cannot be used. (11) (31) (32) (80) multi-connectors ?-req? ?s? ?ot-a? ?-enbl? ?m?cannot be used. the replace case terminal is not provided with a connector for communication.
pdze t erminal no. t erminal name t erminal no. t erminal name t erminal no. t erminal name t erminal no. t erminal name t erminal no. t erminal name t erminal no. t erminal name t erminal no. t erminal name t erminal no. t erminal name t erminal name remarks analog input analog input digital output analog output analog output analog output analog output analog output signal common digital common grounding instrument power supply - analog input analog input analog input analog input analog input control output control output digital power supply + instrument power supply + digital input digital input digital input digital input digital input digital input digital input digital input digital input digital output digital output digital output digital output digital output digital output digital output digital output digital output digital output note2,3,4 replaced instruments 2 pdze2003 3 cc-m(pdc) replace case terminal controller (type pml-3/cc-f) controller (type pmc-3/cc-e) controller (type pnc/cc-s) manual loder (pmd) manual loder (pnd) 11 i 171 pv 7 1pv71pv11i 31 pv 11 i 14 i 272 cas 72 cas 72 cas 71 cas 31 flt 33 flt 33 flt 33 flt 34 flt 34 flt 55 ao5 m22 mv m22 mv 52, m6 ao2 54, m5 ao2 54, m5 ao2 53 ao3 51 kpv 51 kpv 51 kpv 51 kpv 51 kpv 54 ao4 52 sv 52 s v52sv52sv 51, m5 ao1 53, m4 ao1 53, m4 ao1 53 ao1 53 ao1 56, 57,m11 sc 55, 56,m11 sc 55, 56,m11 sc 54, 55 sc 55, 76 sc 32 sc 55, 76 sc 62,m12,m34 pcd 62, m3 pcd 62, m3 pcd 62 pcd 61 pcd 16 pc note1 61 pcd 63 g 60 g 60 g 60 g 62 g g g 62 g 64 n/ 61 pc 71 ,m7 ai1 58 wo 61 pc 61 pc 60 pc 16 pc note1 60 pc 58 wo 75 wo 54 wo 33 w note5 54 wo 56, 57,m11 sc 59 w 59 w 76 w 75 w 35 w 75 w signal common 72, m8 ai2 74, m7 ai2 74, m7 ai2 73 ai2 73, m9 ai3 75, m8 ai3 75, m8 ai3 74, m10 ai4 76, m9 ai4 76, m9 ai4 75 ai5 77, m10 ai5 77, m10 ai5 m23 do1 78 po 78 po 56 po 56 po 36 po 56 po m24 do2 79 po 79 po 57 po 57 po 37 po 57 po 82, m33 vpd 82, m12 vpd 82, m12 vpd 82 vpd 82 vpd 15 vp note1 82 vpd 83 l/ 81 vp 81 vp 81 vp 81 vp 15 vp note1 81 vp m13 di1 m16 di1 m16 di1 31 pi 32 pi 12 pi 32 pi m14 di2 m17 di2 m17 di2 32 pi 33 pi 13 pi 33 pi m15 di3 m18 di3 m18 di3 m16 di4 m19 di4 m19 di4 m17 di5 m13 di5 m13 di5 80 ex-mc di2 79 di2 m19 di7 m14 pv-trk m14 pv-trk 79 pv-trk di1 80 pv-trk di1 m20 di8 m15 r-ack m15 r-ack 78 r-ack 78 r-ack di3 m21 di9 12 int 12 int m22 di10 13 smv 13 smv 13 smv 15 smv 12 mc 15 smv m23 do1 m28 m28 do1 m24 do2 m29 m29 do2 m25 do3 m30 do3 m30 do3 m26 do4 m31 do4 m31 do4 m27 do5 m32 do5 m32 do5 m28 do6 m33 do6 m33 do6 11 m 13 m 13 m m29 do7 m34 do7 m34 do7 12 ls 14 ls do1 m30 do8 m21 do8 m21 do8 77 r-req 77 r-req do2 m31 do9 m23 h m23 h 58 h 58 h 58 h m32 do10 m24 l m24 l 59 l 59 l 59 l note: terminal numbers on left of each model note: terminal names on right of each model list of terminal numbers and terminal names corresponding to the replacing case and cc-m (wiring should be performed so as to coincide the terminal name of the replaced type with that of the replacing case). note1: connect pc and vp wires to pc and pcd, and vp and vpd, respectively, of the replace case. note2: in case of soft connection (wafer connection) with cc-m, confirm the replace case and cc-m terminals. note3: ai1 terminal on replace case terminal is not connected in the interior (it should not be used). note4: terminals do1 and do2 (multi-connector terminals) on replace case terminal have not been connected internally, and cannot be used. note5: pmd is of different connecting terminal names. be careful. furthermore, terminal names of pml and pmc are also different with i type. be careful. common: screw terminals ?? ?i+? ?i-? ?+? ?di?cannot be used. (11) (31) (32) (57) (80) multi-connectors ?-req? ?s? ?ot-a? ?o1? ?o2? ?-enbl? ?i1?cannot be used. the replace case terminal is not provided with a connector for communication. information in this catalog is subject to change without notice. p rinted in japan sales div. iii, international sales group global business group gate city ohsaki, east tower, 11-2, osaki 1-chome, shinagawa-ku, tokyo 141-0032, japan http://www.fesys.co.jp/eng phone: 81-3-5435-7280, 7281 fax: 81-3-5435-7425 http://www.fic-net.jp/eng caution on safety *before using this product, be sure to read its instruction manual in advance.
|
